Forums Tools and Other Hardware Free ULTRA TEC Parts

Tagged: 

  • Free ULTRA TEC Parts

    Posted by markaoros on January 7, 2021 at 10:01 am

    Be fair and only get them if you need them.
    First person to say “dibs” gets them.
    You pay the shipping (USPS Priority Small Flat Rate Box).

    More stuff to come in various categories.
    Cleaning up the studio and want to help my USFG colleagues.

    carldowney replied 11 months ago 8 Members · 20 Replies
  • 20 Replies
  • markaoros

    Member
    January 12, 2021 at 8:50 am

    No longer available.

  • fireagate223

    Member
    January 15, 2021 at 2:30 pm

    looking forward to more Ultra Tec any change there are dops and a spindel?

  • gemmakermz

    Member
    February 9, 2022 at 1:34 pm

    i have made a replacement three part pan for my ultra tec. no more pulling down of rubber pan and the extreme mess. i have made a 3D printed pan that is easy to remove and uses two rings one full for regular cutting and one for 90 degree use.
    gemmakermz@cs.com. see second posting below for rest of pictures

    • This reply was modified 2 years, 5 months ago by  gemmakermz.
  • gemmakermz

    Member
    February 9, 2022 at 1:38 pm

    more pictures.

  • gemmakermz

    Member
    February 9, 2022 at 1:39 pm

    one more picture. i now make the new pan.

  • markaoros

    Member
    February 9, 2022 at 2:53 pm

    Very cool. Well done!!!

  • samfacet

    Moderator
    February 20, 2022 at 10:14 am

    That is a nice job!

  • jmee

    Member
    May 6, 2022 at 6:09 am

    Why make two separate rings on the splash bowl? Why not just a small piece to cover the slot for the girdle? It can be a simple piece that hangs over the edge like on a Facette, or since you’re designing it from the ground up it could slide into or around a notch you design on the edges girdle slot.

    I’m wary of 3D printing splash bowls. 3D printed parts can leak if exposed to standing water, like if the drain clogs. Ruining a motor or motor controller isn’t worth the risk unless there’s no other option. If you make one for someone else, who’s responsible if it leaks? I would suggest sealing the bowl with a sealant to be safe.

  • fireagate223

    Member
    May 26, 2022 at 8:37 am

    I see you have a splash bowl any chance you might have a ferrule for inside the spindle? Joan

  • markaoros

    Member
    May 26, 2022 at 9:47 am

    I do not.

  • rickvaile

    Member
    July 21, 2022 at 10:37 pm

    Does anyone know where I could get a dop chuck for an older Ultra Tec V2? This machine is a paper weight without it.

    • Bobdrbob

      Member
      July 31, 2022 at 8:56 pm

      I HAVE ONE FROM MY MACHINE. IT IS SERIAL NUMBER 997R IT IS A 1979 MODEL I BELIEVE. It was Glenn Klein’s machine. Email me at Alivetodaysofar@gmail.com I won’t be able to send pics till Saturday but if I remember correctly I have one I may be able to part with to help you out.

  • rickvaile

    Member
    July 21, 2022 at 10:40 pm

    Any place to look for a used Ultra Tec. I think I have checked everywhere. There has to be some out there for sale.

  • rickvaile

    Member
    July 22, 2022 at 10:34 am

    I have a 1980 Ultra Tec V2 missing a dop chuck. (basically a paper weight) Do you have any idea where I can buy one?

  • markaoros

    Member
    July 24, 2022 at 5:02 pm

    All the parts are gone. I do not know where to get additional parts.

  • gemmakermz

    Member
    July 22, 2023 at 4:16 pm

    replacement parts are no longer made for the V2’s however if you need a part contact me as i’ve been a ultra tec user for 59 years and knew howard stanley and joe rubin. some parts i can make. i do not make the chucks but can make a quill shaft that take the dop like the V5 does.

Page 1 of 2

Log in to reply.