Forums Tools and Other Hardware Free ULTRA TEC Parts

15 replies, 7 voices Last updated by Bobdrbob 1 month, 4 weeks ago
Viewing 15 posts - 1 through 15 (of 16 total)
  • Author
    Posts
  • #7063

    markaoros
    Participant
    @markaoros

    Be fair and only get them if you need them.
    First person to say “dibs” gets them.
    You pay the shipping (USPS Priority Small Flat Rate Box).

    More stuff to come in various categories.
    Cleaning up the studio and want to help my USFG colleagues.

    #7088

    markaoros
    Participant
    @markaoros

    No longer available.

    #7089

    fireagate223
    Participant
    @fireagate223

    looking forward to more Ultra Tec any change there are dops and a spindel?

    #8372

    gemmakermz
    Participant
    @gemmakermz

    i have made a replacement three part pan for my ultra tec. no more pulling down of rubber pan and the extreme mess. i have made a 3D printed pan that is easy to remove and uses two rings one full for regular cutting and one for 90 degree use.
    gemmakermz@cs.com. see second posting below for rest of pictures

    • This reply was modified 7 months, 3 weeks ago by gemmakermz.
    Attachments:
    You must be logged in to view attached files.
    #8378

    gemmakermz
    Participant
    @gemmakermz

    more pictures.

    Attachments:
    You must be logged in to view attached files.
    #8383

    gemmakermz
    Participant
    @gemmakermz

    one more picture. i now make the new pan.

    Attachments:
    You must be logged in to view attached files.
    #8390

    markaoros
    Participant
    @markaoros

    Very cool. Well done!!!

    #8401

    samfacet
    Participant
    @samfacet

    That is a nice job!

    #8459

    jmee
    Participant
    @JMee

    Why make two separate rings on the splash bowl? Why not just a small piece to cover the slot for the girdle? It can be a simple piece that hangs over the edge like on a Facette, or since you’re designing it from the ground up it could slide into or around a notch you design on the edges girdle slot.

    I’m wary of 3D printing splash bowls. 3D printed parts can leak if exposed to standing water, like if the drain clogs. Ruining a motor or motor controller isn’t worth the risk unless there’s no other option. If you make one for someone else, who’s responsible if it leaks? I would suggest sealing the bowl with a sealant to be safe.

    #8463

    fireagate223
    Participant
    @fireagate223

    I see you have a splash bowl any chance you might have a ferrule for inside the spindle? Joan

    #8464

    markaoros
    Participant
    @markaoros

    I do not.

    #8870

    rickvaile
    Participant
    @rickvaile

    Does anyone know where I could get a dop chuck for an older Ultra Tec V2? This machine is a paper weight without it.

    #8872

    rickvaile
    Participant
    @rickvaile

    Any place to look for a used Ultra Tec. I think I have checked everywhere. There has to be some out there for sale.

    #8881

    rickvaile
    Participant
    @rickvaile

    I have a 1980 Ultra Tec V2 missing a dop chuck. (basically a paper weight) Do you have any idea where I can buy one?

    #8891

    markaoros
    Participant
    @markaoros

    All the parts are gone. I do not know where to get additional parts.

Viewing 15 posts - 1 through 15 (of 16 total)
  • You must be logged in to reply to this topic.